













Stinger Attachments | SPXR Rotating/Oscillating Skid Steer Snow Pusher
Estimated shipping only — your final shipping cost is confirmed at checkout.
The Stinger Attachments SPXR Rotating/Oscillating Skid Steer Snow Pusher is built for high-volume snow removal on parking lots, commercial properties, farmyards, equipment yards, and other large areas where keeping the cutting edge on the ground matters. Its 30″ × 30″ box carries snow forward instead of requiring the repeated scoop-and-dump cycle of a bucket, helping operators make longer, more productive pushes.
What sets the SPXR apart is its rotating/oscillating mount. Instead of holding the entire pusher rigidly on the same plane as the skid steer’s quick-attach plate, the mount allows the box to rock side-to-side as the surface changes. That helps the cutting edge follow crowns, dips, and uneven pavement for more consistent ground contact. Choose from 6′ to 14′ widths, steel or rubber cutting edges, and optional steel or rubber dragback configurations.
Features
- Rotating/Oscillating Mount: Allows the pusher to move side-to-side with changing surface contours for more consistent cutting-edge contact.
- 30″ × 30″ Snow Box: Built to contain and push large volumes of snow through long passes.
- Multiple Widths: Available in 6′, 7′, 8′, 9′, 10′, 12′, and 14′ configurations.
- Steel or Rubber Cutting Edge: Choose the edge that best matches your clearing surface and desired scrape.
- Optional Dragback: Add a steel or rubber dragback for pulling snow away from buildings, doors, curbs, docks, and other areas that cannot be cleared with a forward push.
- Adjustable Wear Skids: 3/4″ wear skids allow cutting-edge height to be adjusted as conditions change.
- Reinforced Moldboard: Upper and lower structural channels support the rear moldboard during heavy pushes.
- Reinforced Interior Corners: Added reinforcement strengthens high-stress areas while keeping the box easier to clean out.
- Heavy Side Plates: 1/4″ Grade 50 steel side plates are used across the lineup.
- Bolt-On Edges: Cutting and dragback edges are replaceable rather than permanently welded in place.
- Box Size: 30″ × 30″
- Available Widths: 6′ | 7′ | 8′ | 9′ | 10′ | 12′ | 14′
- Mount: Rotating/Oscillating
- 6’–10′ Moldboard: 3/16″ Grade 50 steel
- 12’–14′ Moldboard: 1/4″ Grade 50 steel
- Side Plates: 1/4″ Grade 50 steel
- Steel Cutting Edge: 3/4″ × 6″, bolt-on
- Rubber Cutting Edge: 1.5″ × 8″
- Steel Dragback Edge: 1/2″ × 6″, bolt-on
- Rubber Dragback Edge: 1″ × 8″
- Wear Skids: Adjustable 3/4″
- Dragback: Optional
- Mounting Interface: Skid steer quick attach configuration
What does rotating/oscillating mean on the SPXR?
The pusher is able to rock side-to-side relative to the skid steer instead of staying completely rigid with the quick-attach plate. If one end of the pusher encounters a crown, dip, or other change in elevation, the mount allows the box to follow that change more naturally. This helps keep more of the cutting edge in contact with the surface.
Does the SPXR angle left and right like a snow blade?
No. Rotating/oscillating refers to the pusher’s ability to follow uneven ground. It is not a hydraulic angle function for directing snow to one side.
How much does the SPXR oscillate?
Stinger does not publish a degree range for the SPXR’s oscillating movement, so we do not specify an exact angle.
What is the advantage over the standard SPX snow pusher?
The standard SPX uses a more rigid mounting setup. The SPXR adds the rotating/oscillating mount, making it better able to accommodate surface changes across the width of the attachment.
Should I choose a steel or rubber cutting edge?
A steel edge provides a more aggressive scrape and is a good choice when packed snow and ice are a priority. Rubber is more forgiving on pavement and concrete and can flex over small cracks and irregularities.
What does the optional dragback do?
The dragback gives you a rear-facing edge for pulling snow away from garage doors, loading docks, buildings, curbs, parked equipment, and other places where you cannot simply push straight through.
Can I choose a different material for the cutting edge and dragback?
Yes. The cutting edge and dragback are separate selections, so the snow pusher can be configured with a steel or rubber cutting edge and no dragback, a rubber dragback, or a steel dragback.
Why use a snow pusher instead of a bucket?
A pusher contains snow and keeps moving it forward rather than requiring the operator to scoop, carry, dump, and return after every load. On large open areas, that can significantly reduce the number of machine movements needed to clear snow.
What size SPXR should I choose?
Match the pusher width and weight to your machine’s operating capacity, traction, ballast, and the snow conditions you normally encounter. A wider pusher can move considerably more snow, but it also puts a larger load in front of the machine. The 12′ and 14′ configurations especially require an appropriately sized carrier.
Note: The SPXR is a large, heavy snow pusher. Compatibility depends on the machine’s quick-attach interface, rated operating capacity, lift capacity, traction, ballast, selected pusher width, and expected snow load. Larger widths are not appropriate for every skid steer or compact track loader.
Common Compatible Machines
Bobcat: S650, S66, S740, S76, S770, S850, S86, T650, T66, T740, T76, T770, T870
Caterpillar: 246D3, 262D3, 272D3, 259D3, 279D3, 289D3, 299D3, 255, 265, 275, 285
John Deere: 324G, 330G, 332G, 325G, 331G, 333G, 331 P, 333 P, 335 P
Kubota: SSV75, SVL75-3, SVL97-3
CASE: SR240B, SR270B, SV280B, SV340B, TR340B, TV370B, TV450B, TV620B
New Holland: L328, L334, C332, C337, C345
Takeuchi: TL10V2, TL12R2, TL12V2
Gehl: R260, R280, V270, V330, RT210, RT255
Mustang: 2600R, 2700V, 3300V, 2100RT, 2500RT
ASV: RT-75, RT-135, VT-80, VT-100
JCB: 270, 300, 325T, 3TS-8T
Wacker Neuson: SW28, SW32, ST45, ST50
Yanmar: TL75VS, TL80VS, TL100VS
Stinger Attachments backs the SPXR with a 2-year manufacturer warranty against defects in materials and workmanship for the original purchaser.
Better Contact on Uneven Lots
The oscillating mount lets the pusher react to changes across the surface instead of forcing both ends of a wide cutting edge to stay on exactly the same plane. That is especially useful on crowned pavement, transitions, and lots that are not perfectly flat.
Move Snow Without Constant Dump Cycles
The 30″ × 30″ box is designed to keep a large volume of snow moving ahead of the machine, making the SPXR well suited to long pushes across commercial lots, farmyards, and equipment yards.
Configure the Edge for the Job
Steel gives you a more aggressive scraping setup, while rubber offers a more forgiving edge for paved surfaces. The dragback can be configured separately, giving you more control over how the pusher is set up.
Clean Up Around Obstacles
Adding a dragback turns areas around doors, docks, curbs, and buildings into a much easier job. Pull the snow into an open area, reposition, and push it to the pile.
- Commercial snow removal
- Parking lots
- Farm and equipment yards
- Large paved properties
- Municipal and facility maintenance
- Loading areas
- Long driveways and private lanes
- Uneven or crowned pavement
- Snow removal around buildings and loading docks
- High-volume snow pushing

Why buy from ECHO Eqpt?
At ECHO Eqpt, we actually use and support the equipment we sell. You’re not getting generic answers, you are talking to people who understand how this equipment works in the field. That means faster answers, better recommendations, and no wasted time trying to figure things out on your own.
We’re easy to work with. If something breaks, tell us what actually happened and be honest with us (a good sense of humor doesn’t hurt either). We’re often known to help out even outside of standard warranty terms. And if it’s on us, we’ll own it and make it right. No excuses, no finger pointing - just real support when it matters.









