Estimated shipping only — your final shipping cost is confirmed at checkout.
The Digga DR6 Rock Auger Bit is built for drilling in shale, fracturable rock, and hard rock where a standard earth or combination auger isn’t enough. It uses rotating carbide rock picks that bite into hard material while turning as they work, helping spread wear across the cutting surface.
Designed for larger drilling setups in the 4.5–15 ton machine range, the DR6 is available in diameters from 6″ to 36″. Its shorter flighting helps clear broken rock from the hole more often, reducing buildup around the cutting head and making it easier to check the teeth during demanding drilling work.
What kind of ground is the DR6 made for?
The DR6 is designed specifically for rock drilling, including shale, softer fracturable rock, and hard rock.
How much auger-drive torque do I need?
The DR6 needs substantially more torque than an earth auger. As a general guide, 6″–12″ DR6 bits should be paired with a drive producing around 3,550 ft-lb or more. For 14″–18″ bits, look toward the 3,900–4,900+ ft-lb range. A 24″ bit should be paired with roughly 4,900 ft-lb or more, while 30″–36″ rock bits belong with higher-torque drives around 6,100 ft-lb or above. Rock hardness can change these requirements, so larger DR6 setups should be verified before ordering. (Torque figures are approximate sizing guidance. Confirm that your drive also has the correct output shaft, and that your machine can supply the drive’s required hydraulic flow and pressure.)
What hydraulic flow and pressure do I need?
The DR6 does not have one fixed hydraulic requirement because the auger bit is driven by a separate auger drive. Digga drive models in the DR6 range use approximately 10–48 GPM depending on drive size, with maximum pressure ratings up to 3,500 PSI. Check the specifications of your auger drive, and make sure your machine can supply flow and pressure within that drive’s operating range.
How is the DR6 different from the RC4?
The RC4 is a combination auger for jobs where you may move between dirt, clay, shale, and softer rock. The DR6 is a dedicated rock-drilling bit with rotating carbide rock picks for much harder conditions.
Can I use the DR6 in regular soil?
It can pass through soil on the way to rock, but it is not designed as a general-purpose earth auger. If most of your drilling is in dirt or mixed earth and rock, the A4 or RC4 will usually be a better fit.
What are rotating rock picks?
They are carbide-tipped cutting teeth that rotate as they contact the rock. This helps distribute wear around the tooth rather than concentrating it in one spot.
Can the rock picks be replaced?
Yes. The cutting picks and pilot components are replaceable wear parts.
What auger drive does the DR6 use?
The DR6 is designed for compatible Digga 5DD through 12DD auger drives. The correct drive depends on the host machine, hydraulic output, rock conditions, and auger diameter.
What hub does the DR6 use?
The standard DR6 uses a 2.5″ hex hub. A 2″ hex hub is also available from Digga, but the standard configuration for this product is 2.5″.
Can I add an auger extension?
Yes. The standard 2.5″ hex DR6 is compatible with Digga XO25 outer extensions and XT25 inner extensions.
Does every machine work with every DR6 diameter?
No. Larger rock augers require more torque. Your machine, auger drive, ground conditions, and desired diameter all need to be considered when choosing a setup.
Note: The DR6 Rock Auger Bit requires a compatible auger drive and machine-specific mount. Machine size alone does not determine fitment. The host machine must be able to run the selected drive, and the drive must provide enough torque for the selected bit diameter and rock conditions.
Common Compatible Machines
Digga augers are covered by a 1-year manufacturer warranty against defects in materials or workmanship.
Drill where earth augers can’t.
The DR6 is made specifically for rock conditions, giving you a cutting setup designed for shale, fracturable formations, and hard rock.
Spread wear across the cutting teeth.
The rotating carbide rock picks turn as they work, helping distribute wear and maintain cutting performance.
Clear broken material from the hole.
Shorter flighting encourages more frequent spoil removal, helping move broken rock away from the cutting head.
Replace wear parts instead of the whole bit.
Rock picks and pilot components can be replaced individually as they wear.
At ECHO Eqpt, we actually use and support the equipment we sell. You’re not getting generic answers, you are talking to people who understand how this equipment works in the field. That means faster answers, better recommendations, and no wasted time trying to figure things out on your own.
We’re easy to work with. If something breaks, tell us what actually happened and be honest with us (a good sense of humor doesn’t hurt either). We’re often known to help out even outside of standard warranty terms. And if it’s on us, we’ll own it and make it right. No excuses, no finger pointing - just real support when it matters.
Shipping & Freight Delivery | Returns, Refunds & Cancellations | Terms & Conditions of Sale | Privacy Policy
Iowa eCommerce Website by Wapiti Digital
